Termékek tribo por bevonat (23)

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Cortec VpCI® 391 Water Based Temporary Coating. Safeguard your metal parts and equipment from corrosion with Cortec VpCI® 391.This innovative, water-based coating provides exceptional protection against rust, tarnish, and other forms of corrosion.Utilising Cortec's patented Vapor phase Corrosion Inhibitor (VpCI®) technology, it creates a transparent, protective barrier that shields metal surfaces during storage and transit. Easy to apply by spraying, brushing, or dipping, VpCI® 391 dries quickly to a non-tacky finish, allowing for immediate handling. Environmentally friendly and free of hazardous chemicals, this versatile coating protects a wide range of metals, including steel, aluminium, and copper.Ideal for machinery, tools, automotive components, and more, VpCI® 391 offers up to 2 years of indoor and 6 months of outdoor protection.Simply remove with water when ready for use.

Tantalum alloy powders offered by SAM are characterized by their high melting point, excellent corrosion resistance, and outstanding thermal and electrical conductivity. These features make them ideal for various high-performance industries, including aerospace, electronics, and chemical processing.

CoolDry ist eine hochwertige und dauerhaft flexible Dachbeschichtungsfarbe, die ca. 80 % der direkten Sonneneinstrahlung reflektiert und so wirkungsvoll und energiesparend die Erwärmung von Gebäuden, Fahrzeugen und anderen Objekten verhindert. Nicht nur die helle Grundfarbe des Materials, sondern vor allem die Vielzahl kleinster, beschichteter, hohler Hightech-Glas-Reflexionskörper bewirkt eine Verringerung der Dachtemperatur um bis zu 40 °C und sorgt so für deutlich kühlere Innenraumtemperaturen sowie signifikant reduzierte Klimatisierungskosten.

Référence COLLEFIBRE-5KG

Colle de contact transparente à base polyuréthane - spécial PVC doux Pour double encollage de matériaux divers, durs ou flexibles, comme la plupart des matières synthétiques (PVC souple, PVC, ABS, plexi, polycarbonate), bois, panneaux de revêtements décoratifs stratifiés, placage et collage sur champ, nez de marches et marches d’escalier, plinthes en PVC, cuir, liège, textile, métaux entre eux ou sur bois, pierre, béton, plâtre, métal et autres supports lisses et non poreux. Spécifiquement pour des applications dont la couche de colle ou le joint de colle reste visible : comme le collage sur verre ou plexi. Aussi idéal pour la réparation de bâches, toiles de tente et pour matériaux gonflables en PVC souple. Prête à l'emploi, transparente au séchage, pas de trace brune, utilisation aisée à la brosse et au peigne à colle, force d'adhérence progressive rapide, résistante à l'humidité à la chaleur et au froid (-10°C jusqu'à +70°C) Résiste aux acides légers et bases Sans...

Bei TRADIUM ist Cer in Form von Cer-Metall und Cer-Oxid fü den Industriebedarf erhältlich. Lieferbare Formen - Cer-Metall - Cer-Oxid Benötigen Sie Cer mit besonderen Lieferformen oder Spezifikationen? Dann kontaktieren Sie uns! Wir helfen Ihnen gerne bei Ihrem Anliegen. Ihr Ansprechpartner für Cer ist: Jan Giese Tel.: +49 (0)69 50 50 250 - 237 Wir freuen uns auf Ihre Anfrage!

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Polyurea Spray-Soft SYNTECH POLYUREA PRIMER is a two-component formulation based on epoxy resin in combination with cycloaliphatic amine hardeners. It is characterised by high values of penetration ability, and reinforcement, with particular reference to concrete surfaces, and is also indicated on most media and surfaces found in the building industry. Specific for the preparation of surfaces prior to coating them with SYNTECH POLYUREA SPRAY. Preparation of media and building surfaces (concrete, ceramics, wood, glass, cement, etc.), prior to coating them with SYNTECH POLYUREA SPRAY. The surfaces of application will be conveniently seasoned, prepared, adequately strong and absorbent; exempt from phenomena of rising damp surface, dust, grease, soiling, crumbling and non-adhering parts, hydro-repellent coatings or detected humidity. For more degraded floorings, in addition, preliminary shot peening or milling of the surfaces may be required. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at a low number of revolutions, or with a suitable worksite tool, for about 2 minutes, until a smooth lump-free mixture is obtained. Lay a homogeneous layer of product on the previously prepared surfaces to be treated, preferably by roller or brush. Thanks to the particular chemical structure of the amine curing used, SYNTECH POLYUREA PRIMER is responsive and effective even in cold weather. Barrel 225 kg [A] - Barrel 200 kg [B] - Kit: 1 Barrel 225 kg [A] + 1 Barrel 200 kg [B]

Protech WAC-RC Single-component colored finish in water dispersion for the opaque protection of concrete surfaces and cementitious substrates, wall coverings, and appropriately prepared and primed floors. The product is a painting system suitable for environments with the presence of food, which can be used to protect walls and ceilings that comply with the HACCP protocol, in order to prevent possible food contamination. Excellent resistance to atmospheric agents and aggressive industrial environments Good water vapor permeability and water repellency Wide range of colors available Uniform matte finish Low maintenance over time Good resistance to diluted acids and alkalis, fuels and hydrocarbons Excellent resistance to detergents and disinfectants Excellent resistance to mold attack Perfectly washable It meets the following requirements: Legislative Decree n. 193 of 06/11/2007 “Implementation of Directive 2004/41/EC relating to food safety controls and application of community regulations in the same sector” - HACCP UNI 11021:2002 “Products and systems for painting environments with the presence of food”, in particular it is suitable for walls, ceilings and surfaces for which resistance to washing is required; can be washed with chloroactive detergent (detergent A); can be washed with alkaline degreaser (detergent B); can be washed with acid descaler (detergent C); can be washed with disinfectant (detergent D); resists temperature changes. Colored protective finish of concrete surfaces, cement plasters Anti-carbonation finishing of concrete structures Wall finishing for food, wine and butcher shops Wall finishing for chemical and pharmaceutical industries Finishing and coating of suitably prepared metal surfaces Protective finish for floors already treated with resins or primed Protective treatment of oxidized asphalt surfaces Finish for environments in the presence of food. Concrete The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the coating such as dirt, grease, oil, traces of coatings and surface treatments, etc. Any weak or detaching parts must be removed before applying the product by mechanical sanding with diamond discs and dust extraction. The tensile strength must not be less than 1.5 N/mm². The application of Protech WAC-RC on new or particularly absorbent cementitious substrates must always be preceded by the application of a coat of Protech fix AC water-based anchoring primer. Wait 3-4 hours before applying the finish. Resin coatings The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the coating such as dirt, grease, oil, etc. Sand the surface by mechanical sanding with diamond discs and dust extraction. It is advisable to wash the surfaces and wait for them to dry completely before applying the finish. The application of Protech WAC-RC on resinous and multilayer systems must always be preceded by sanding the entire surface in order to promote and guarantee optimal adhesion of the product to the support. PVC Wash the PVC surfaces to be treated with specific detergents to remove any substances that may affect the adhesion of the coating such as dirt, grease, oil, materials that block the pores in order to promote better capillary penetration of the product into the support. The application of Protech WAC-RC on PVC supports can be carried out directly with appropriate dilutions of the product in first and second coat. Steel Any welding residues must be removed and the joints sanded. Sandblast to cleanliness level Sa 2½ according to ISO8501-1. The surfaces to be coated must be free from dirt, oil, grease and impurities. Average surface roughness degree RZ ≥ 50 μm. An anti-corrosion treatment is recommended before applying the coating. The application of Protech WAC-RC on steel supports must always be preceded by the application of a coat of “surface tolerant” epoxy-polyamide primer in the solvent phase Syntech Poliurea Primer Epoxy Metal. Approximately 0.20 kg of Protech WAC-RC for each square meter of surface to be painted for each coat. Apply two coats.. Packaging: 20 kg bucket UM: €/kg

Cortec VpCI® 386 Coating is a cutting-edge, water-based acrylic topcoat engineered to deliver superior corrosion protection for diverse metal substrates. Developed by corrosion prevention experts at Cortec Corporation, this innovative coating harnesses VpCI® technology to create an invisible shield against rust and oxidation. Environmentally friendly and easy to apply, it offers exceptional adhesion, durability, and versatility across various industries.Ideal for industrial equipment, manufacturing, automotive, marine, and construction applications, Cortec VpCI® 386 provides reliable protection while meeting stringent environmental standards.

Cortec VpCI® 380 Railcar Coating. Protect your railcars with Cortec VpCI® 380, a cutting-edge, water-based acrylic coating.This innovative solution offers superior corrosion protection, directly applied to metal without primer. Enjoy long-lasting durability against harsh weather, easy application, and an attractive finish.Ideal for railcars, trucks, and more. Protects ferrous and non-ferrous metals.Maintain your fleet's value with Cortec VpCI® 380.

Cortec VpCI® 382 Water-Based Urethane Topcoat. Protect against corrosion, abrasion, and weathering with this high-performance, water-based polyurethane topcoat. Featuring Cortec's VpCI® technology, it offers multi-metal corrosion protection, creating a molecular shield that safeguards both coated and nearby metal surfaces.VpCI® vapours reach hidden areas, eliminating the need for separate corrosion inhibitors. The durable finish resists damage and comes in various colours. Easy to apply and clean, this low-VOC, water-based coating is ideal for industrial equipment, structures, vehicles, and more.Enjoy long-lasting protection and a professional look with this cost-effective solution.

CoolDry ist eine hochwertige und dauerhaft flexible Dachbeschichtungsfarbe, die ca. 80 % der direkten Sonneneinstrahlung reflektiert und so wirkungsvoll und energiesparend die Erwärmung von Gebäuden, Fahrzeugen und anderen Objekten verhindert. Nicht nur die helle Grundfarbe des Materials, sondern vor allem die Vielzahl kleinster, beschichteter, hohler Hightech-Glas-Reflexionskörper bewirkt eine Verringerung der Dachtemperatur um bis zu 40 °C und sorgt so für deutlich kühlere Innenraumtemperaturen sowie signifikant reduzierte Klimatisierungskosten.

At TRADIUM, hafnium is available in the following forms for industrial supplies: - Hafnium metal: rods, pieces, sponge, ingots, round bars, wires, sheets, plates - Hafnium hydride powder - Hafnium oxide - Semifinished and finished products and manufacturing according to specifications Your point of contact for hafnium is: Frank Meier Phone: +49 (0)69 50 50 250 - 234 We are looking forward to hearing from you!

Titanium-based powder is a high-performance material widely used in various advanced industries, including aerospace, biomedical, automotive, and additive manufacturing. Known for its exceptional strength-to-weight ratio, corrosion resistance, and biocompatibility, this powder is ideal for producing lightweight yet durable components.

Référence GCMOULEPIN-5KG

Référence GCNOIRPISFIN-1KG

Référence GC5892PIN-25KG

Référence GCNOIRPIS-25KG

Référence GCNOIRPIN-5KG

Référence GCMOULEPIN-25KG

Référence GCBLANPISFIN-5KG